Design and Construction of Special Tools for Rear Seal Removal and Installation on Komatsu Engine Flywheel Housing
##plugins.themes.academic_pro.article.sidebar##
Downloads
##plugins.themes.academic_pro.article.main##
Abstract
This research focuses on the innovation of mechanical work aid design in the form of special tools specifically used to remove and install the rear seal on the flywheel housing of Komatsu diesel engines type SAA6D107E-1 and SAA4D95LE-3. One of the procedures that is still done manually and has high risk is the replacement of the rear seal on the flywheel housing. The purpose of using special tools is to gain efficiency in the removal and installation of the rear seal on the flywheel housing. The research method includes field observation, component measurement, 2D and 3D design, and direct field trials. The test results show that this tool can reduce the processing time from 55 minutes to 20 minutes. The use of these special tools helps technicians in increasing the work speed in removing and installing without causing damage to other components.
##plugins.themes.academic_pro.article.details##
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
References
[2] Jenni Ria R, et al (2021). Analisis Ketahanan Seal Pada Batang Hidrolik Excavator Tipe EC200. Jurnal Baut dan Manufaktur Fakultas Teknik Mesin. Vol 3, No.02.
[3] AlbertG. “Elmentsof PhysicalMetallurgy” Edisi ke3, 1974,New Delhi110001, India.
[4] Utomo K Y, (2022). Analisis Ketahanan Seal pada Batang Hidrolik Excavator Tipe EC200D. Jurnal Kewarganegaraan Vol. 6 No. 4 Desember 2022
[5] Susilawati, et al (2019) Proses Manufaktur Alat Bantu Khusus (Special Service Tools) Pelepas Seal Suspensi Depan Jenis Telescopic Fork Sepeda Motor. Jurnal Ilmiah Ilmu dan Teknologi Rekayasa Volume 2 Nomor 1, Maret 2019 21-25.
[6] Van Harling, V. N., et al. (2020). Pengaruh Variasi Penyetelan Katup Terhadap Putaran Pada Engine Stand Motor Bensin. Jurnal Pendidikan Teknik Mesin Undiksha.
[7] Rasma, Ari Aryadi. "Pembuatan Alat Remove dan Install Track Roller Pada Unit PC 200-
8MO untuk General Over Haul." Prosiding Semnastek (2022).
[8] Armas, RF et al (2024). Design and Build Special Service Tools for Removing and Install the Drive Shaft for the Komatsu HD785-7 Dump Truck. Jurnal E-Komtek Vol. 8 No. 1 (2024) pp. 199 – 206.
[9] Aryadi, A et al (2023). “Design and development of a special service tools sliding hammer for removing injector nozzles on the SAA4D125E diesel engine,” Motivection, vol. 5, no. 3, 2023, ISSN: 2655-7215.
[10] Mardiana, et al (2024). Modifikasi Seal Pada Silinder Hidrolik Center Post Mitsubishi Dengan Uji Tekan 140 Bar. Jurnal Ilmiah Teknik Mesin 10 (2), pp 59-66
[11] Yoshimura, Masataka, “System design optimization for product manufacturing.” Springer Science & Business Media, 2010.
[12] Purwono, H., et al. (2022). Pembuatan alat bantu khusus pelepasan dan pemasangan piston seal cylinder hydraulic unit excavator PC200-8M0. Prosiding Semnastek.
[13] S. Sunardi, R. Lusiani, and A. Opera Fitra, “Pengaruh Pack Carburizing Dan Kekasaran Permukaan Terhadap Umur Fatik Material Poros Baja S45C”, Journal Foundry, vol. 3, no. 2, pp. 7-12, Feb. 2022.
[14] Zulkarnain Fatoni, & Sukarmansyah. (2018). Perencanaan Alat Bantu Untuk Memasang Torak (Piston Installer). Jurnal Desiminasi Teknologi, 6(1), 1–94.
[15] Farrel, R., et al. (2025). Perancangan flywheel holder yang ergonomis untuk mempercepat proses kerja. Jurnal Mitra Teknik Industri, 4(2), 136–145.